Problem with preparing phase
Hey guys.
I've tested the new version with a ~6 hours stream and put the Project-File into CQMatic but if I start I can only read: Quote:
|
Re: Problem with preparing phase
Quote:
Nothing else in the log :?: Does TMPGEnc run :?: Post your log. -kwag |
Yes that's it. I click "Prediction" and the Programm seems to works but only in preparing phase and it doesn't go on.
|
Re: Problem with preparing phase
Quote:
I've experienced the above message and waiting, with the program finally progressing after 5 or 10 minutes. Only on one occasian did I reboot to get it to work after 10 minutes or so. Most times, it begins executing immediately. It is a infrequent occurance and hasn't been a big problem so far. It only seems to occur with some PVR-250 captures. I will post a log if it occurs again. |
Are you using Directshowsource in the script ?
|
No. I've merged 3 DVD Movies with DVD2AVI to one D2V File and load it with the optimal script, but it doesn't work. I can't say what it is. The programm only prepare. :?
|
Quote:
|
Is there a specific reason for using DirectShowSource?
|
Quote:
|
PVR-250 spits out MPEG-2 so the way to go is d2v->MPEG2Source :wink:
|
Quote:
|
Quote:
|
even if it would be a mjpeg capture, the vfw-decoder within ffdshow is capable decoding mjpg. So Avisource() as it uses vfw also when importing avi captures is the way to go. :wink:
|
same error as original poster
I'm having the same problems as the original poster. I'm using the optiimal script as well. The program stops functioning on the "preparing" phase, but continues to say "Busy" and it looks like its still working, but it's not. Any suggestions?
## DLL Section ## # LoadPlugin("C:\Program Files\AviSynth 2.5\plugins\DGDecode.dll") LoadPlugin("C:\Program Files\AviSynth 2.5\plugins\grip.dll") LoadPlugin("C:\Program Files\AviSynth 2.5\plugins\STMedianFilter.dll") LoadPlugin("C:\Program Files\AviSynth 2.5\plugins\asharp.dll") LoadPlugin("C:\Program Files\AviSynth 2.5\plugins\unfilter.dll") LoadPlugin("C:\Program Files\AviSynth 2.5\plugins\undot.dll") # #### ## Main section and static filters ### # Mpeg2Source("G:\Below_d2v\Below.d2v") # undot() asharp(1, 4) GripCrop(720, 480, overscan=1, source_anamorphic=true, dest_anamorphic=true) GripSize(resizer="BicubicResize") STMedianFilter(3, 3, 1, 1 ) MergeChroma(blur(1.5)) MergeLuma(blur(0.1)) # # ## Linear Motion Adaptive Filtering ## # # ( Portions from AviSynth's manual ) # This will apply variable temporalsoften # and variable blur. # Both filters are active at all times, and work inversely proportional to the # activity, measured from current frame to next frame. ScriptClip(" nf = YDifferenceToNext()" +chr(13)+ "unfilter( -(fmin(round(nf)*2, 100)), -(fmin(round(nf)*2, 100)) ).TemporalSoften( fmin( round(2/nf), 6), round(1/nf) , round(3/nf) , 1, 1) ") # # # GripBorders() #LetterBox( Your_Values_Here ) # Depends on situation. Use MovieStacker! # # ## Functions ### function fmin( int f1, int f2) { return ( f1<f2 ) ? f1 : f2 } # #### |
Quote:
For me ffdshow is a Direct Show filter and should not be anything else. |
@Kwag
Now, it works but after one hour CQMatic didn't hit the target of 1200Kbps average. The average Bitrate of the last sample was 1400Kbps. That's too much. I use a 450 minutes Movie with a max. Bitrate of 5000Kbps anf min. Bitrate 0 because of more quality in high action scenes. And I use your MA Script. What I've done wrong? |
Quote:
IT CAN'T BE PREDICTED. |
Quote:
|
Site design, images and content © 2002-2024 The Digital FAQ, www.digitalFAQ.com
Forum Software by vBulletin · Copyright © 2024 Jelsoft Enterprises Ltd.