KVCD: Lastest Script for Blockbuster and Nomosmooth Filters?

[syk2c11]

Kwag,
Would you please post the LASTEST script for blockbuster and nomosmooth filters again, because the "Addnoise" thread had so many amendment, thanks!

[kwag]

Quote:

Originally Posted by syk2c11

Kwag,
Would you please post the LASTEST script for blockbuster and nomosmooth filters again, because the "Addnoise" thread had so many amendment, thanks!

Sure! Here's what I'm currently using:

NoMoSmooth()

######## Auto Strength, proportional strength depending on resolution #####
## Remove only one "#" on front of the resolution that matches your encoding.

BB_Resolution = 352*240
#BB_Resolution = 352*480
#BB_Resolution = 528*480
#BB_Resolution = 544*480
#BB_Resolution = 704*480

BB_StrengthConstant = 352 * 240 * 20 # Base strength
StrengthValue = round (BB_StrengthConstant / BB_Resolution)
Blockbuster( method="noise", detail_min=1, detail_max=10, lv=1 ) # Apply noise if complexity is <= 10%.
Blockbuster( method="sharpen", detail_min=20, detail_max=90, strength=StrengthValue) # Sharpen only if complexity is >= 20% AND <=90%.

# The last ~10% is left untouched (pass-through), to avoid sharpening highest frequency components ( Peak artifacts, sharpest edge, etc. )
##
################## End Auto Strength ####################

Enjoy,
-kwag

[syk2c11]

Hi there,
The size prediction seems not so accurate when using with blockbuster and nomosmooth filters. The final output has a 100MB difference (the final output is 100MB SMALLER than the predicted one) with the predicted size! (I used the standard size prediction button in FitCD)

[kwag]

Quote:

Originally Posted by syk2c11

Hi there,
The size prediction seems not so accurate when using with blockbuster and nomosmooth filters. The final output has a 100MB difference (the final output is 100MB SMALLER than the predicted one) with the predicted size! (I used the standard size prediction button in FitCD)

Change the .95 constant to a higher value. Try 1.1 to 1.2.

-kwag

[vdermerwedz]

Kwag am I right in assuming that I can put 704*576 in my script
and it will do the job as well?

[kwag]

@vdermerwedz,

Yes.

@syk2c11,

I just finished encoding a movie. The predicted file size was 698MB. the actual file size was 682MB. That's still within the correct range. I did this one manually. Not via DVD2SVCD.

-kwag

[CauCauCau]

Quote:

Originally Posted by kwag

BB_StrengthConstant = 352 * 240 * 20 # Base strength StrengthValue = round (BB_StrengthConstant / BB_Resolution)
Blockbuster( method="noise", detail_min=1, detail_max=10, lv=1 ) # Apply noise if complexity is <= 10%.
Blockbuster( method="sharpen", detail_min=20, detail_max=90, strength=StrengthValue) # Sharpen only if complexity is >= 20% AND <=90%.

I'm brand new to Avisynth, so bear with me if I'm being dumb right now. But Why is "StrengthValue = round(BB_StrengthConstant / BB_Resolution) on the same line as BB_StrengthConstant... and behind a comment mark ("#")? Is this just a typo? Should it be:

Quote:

BB_StrengthConstant = 352 * 240 * 20 # Base strength
StrengthValue = round (BB_StrengthConstant / BB_Resolution)
Blockbuster( method="noise", detail_min=1, detail_max=10, lv=1 ) # Apply noise if complexity is <= 10%.
Blockbuster( method="sharpen", detail_min=20, detail_max=90, strength=StrengthValue) # Sharpen only if complexity is >= 20% AND <=90%.

?

Sorry if I'm talking out of a hole in my body that's not my mouth

^Cau

[kwag]

Quote:

Originally Posted by CauCauCau

I'm brand new to Avisynth, so bear with me if I'm being dumb right now. But Why is "StrengthValue = round(BB_StrengthConstant / BB_Resolution) on the same line as BB_StrengthConstant... and behind a comment mark ("#")? Is this just a typo? Should it be:

?

Sorry if I'm talking out of a hole in my body that's not my mouth

^Cau

Thanks Cau,

Cut+paste doesn't necessarily work every time Sorry!
I edited the post.

Thanks,
-kwag

[Holomatrix]

So with this:
## Remove only one "#" on front of the resolution that matches your encoding.

BB_Resolution = 352*240
#BB_Resolution = 352*480
#BB_Resolution = 528*480
#BB_Resolution = 544*480
#BB_Resolution = 704*480

If I change to the second one, do I change this line to?

BB_StrengthConstant = 352 * 240 * 20 # Base strength

Also would this be the correct order:
Resize
fluxsmooth
nomosmooth
blockbuster

Thanks

[kwag]

Quote:

Originally Posted by Holomatrix

So with this:
## Remove only one "#" on front of the resolution that matches your encoding.

BB_Resolution = 352*240
#BB_Resolution = 352*480
#BB_Resolution = 528*480
#BB_Resolution = 544*480
#BB_Resolution = 704*480

If I change to the second one, do I change this line to?

BB_StrengthConstant = 352 * 240 * 20 # Base strength

Also would this be the correct order:
Resize
fluxsmooth
nomosmooth
blockbuster

Thanks

Hi Holomatrix,

You only remove one "#' from the block. So for 352x480, it would be this:

#BB_Resolution = 352*240
BB_Resolution = 352*480
#BB_Resolution = 528*480
#BB_Resolution = 544*480
#BB_Resolution = 704*480

No other lines need to be changed.
As for the filter order, it is correct.

-kwag