CQMatic calls to TMPGEnc
I am having occasional issue with CQMatic, where it calls TMPGEnc in a loop - but TMPGEnc only flashes on the screen.
TMPGEnc eventually comes back with "Illegal Stream Format" I have seen warnings about setting source ranges - which I have not done. This issue happens after I Execute, then cancel. And then try to Execute again. Once this "issue" happens - I cannot get rid of it. Any Suggestions???????? |
Re: CQMatic calls to TMPGEnc
Quote:
Kwag, I have attached a typical CQMATIC log. Maybe you can see something in it? Log:- http://www.kvcd.net CQMatic Version 1.2.02 Copyright Softronex Corporation, 2003. All rights reserved. Time: 14:57:06 Date: 10/26/2003 Ready! Project: D:\VideoData\video.tpr Creating: CQMatic.tpr D:\VideoData\video.m1v Project resolution: 352x576 Execute. Movie Time: 84 Average Bitrate: 1175 Full Encode mode Executing Prediction Phase... Process started at 14:57:58 On 10/26/2003 Setting up initial sampling. Using CQ_VBR of 60.00 Prediction cycle #1 Encoder started... Process time: 0.05 minutes. Encoder end. File size difference = 18.813581 Low fence: 60.000000 High fence: 90.000000 Last CQ = 60.00 Current CQ = 75.00 CQ difference = 15.000000 Using CQ_VBR of 75.00 Prediction cycle #2 Encoder started... Process time: 0.05 minutes. Encoder end. File size difference = 18.813581 Low fence: 75.000000 High fence: 90.000000 Last CQ = 75.00 Current CQ = 82.50 CQ difference = 7.500000 Using CQ_VBR of 82.50 Prediction cycle #3 Encoder started... Process time: 0.05 minutes. Encoder end. File size difference = 18.813581 Low fence: 82.500000 High fence: 90.000000 Last CQ = 82.50 Current CQ = 86.25 CQ difference = 3.750000 Using CQ_VBR of 86.25 Prediction cycle #4 Encoder started... Process time: 0.03 minutes. Encoder end. File size difference = 18.813581 Low fence: 86.250000 High fence: 90.000000 Last CQ = 86.25 Current CQ = 88.13 CQ difference = 1.875000 Using CQ_VBR of 88.13 Prediction cycle #5 Encoder started... Process time: 0.05 minutes. Encoder end. File size difference = 18.813581 Low fence: 88.125000 High fence: 90.000000 Last CQ = 88.13 Current CQ = 89.06 CQ difference = 0.937500 Using CQ_VBR of 89.06 Prediction cycle #6 Encoder started... Process time: 0.05 minutes. Encoder end. File size difference = 18.813581 Low fence: 89.062500 High fence: 90.000000 Last CQ = 89.06 Current CQ = 89.53 CQ difference = 0.468750 Using CQ_VBR of 89.53 Prediction cycle #7 Encoder started... Process time: 0.05 minutes. Encoder end. File size difference = 18.813581 Low fence: 89.531250 High fence: 90.000000 Last CQ = 89.53 Current CQ = 89.77 CQ difference = 0.234375 Using CQ_VBR of 89.77 Prediction cycle #8 Encoder started... Process time: 0.05 minutes. Encoder end. File size difference = 18.813581 Low fence: 89.765625 High fence: 90.000000 Last CQ = 89.77 Current CQ = 89.88 CQ difference = 0.117188 Final CQ value is 89.77 Encoding set to Full encode. Full encode start... CQMatic complete! Total minutes of process: 0.38 Process ended at 14:58:21 On 10/26/2003 I have had this issue for a couple of weeks, hope someone has some suggestions. |
There are a lot of thread on this problem. Do you read the forum sometimes ?
See last one (especially the first post of racer99) : http://www.kvcd.net/forum/viewtopic.php?t=7037 Note: you still not do anything to the range setting ? That is one of the most important thing to do. Normally all is well explained on the DL page of cqmatic on this forum. |
I have the same error, and searching in the search engine of this site I found the fix to my problem, I saw what is your problem too, thanks a post from Kwag, please, read becarefull and step to step to resolve your problem. I did, and now is working fine, may be a bug from CQMatic, I think.
Here you are the post: http://www.kvcd.net/forum/viewtopic....+stream+format Enjoy ! |
Site design, images and content © 2002-2024 The Digital FAQ, www.digitalFAQ.com
Forum Software by vBulletin · Copyright © 2024 Jelsoft Enterprises Ltd.