Go Back    Forum > Search Forums
Reload this Page Search Results
Ask Question Join / Register   FAQ     Today's Posts
Showing results 1 to 10 of 10
Search took 0.00 seconds. Search: Posts Made By: OldAT
Forum: Video Hardware Repair 05-05-2024, 12:36 AM
Replies: 6
Views: 1,063
Posted By OldAT
Came back to this after some time, the little...

Came back to this after some time, the little gear on the motor had the most hairline crack through it, applying some glue resolved the mechanism issues. Thanks for the tip. I've also taken...
Forum: Video Hardware Repair 10-30-2023, 12:58 AM
Replies: 1
Views: 668
Posted By OldAT
Toshiba V-31A Noisy Playback

I have been given a Toshiba V-31A Beta VCR, it had been sitting for a number of years and I was hoping to be able to playback some of the tapes that belonged to my folks.

I've replaced all the...
Forum: Video Hardware Repair 09-07-2023, 07:18 AM
Replies: 6
Views: 1,063
Posted By OldAT
I dismantled what I could and cleaned off old...

I dismantled what I could and cleaned off old grease and applied some new stuff. It actually does move but the part I circled earlier needs a bit of pressure just to get started, then it runs through...
Forum: Video Hardware Repair 09-03-2023, 04:40 AM
Replies: 6
Views: 1,063
Posted By OldAT
Panasonic DMR-EZ47V tape mechanism partially loading?

Hello,

A mate gave me 2x DMR-EZ47V combo units he asked me to get going. The power supplies both need re-capping as is the usual case with these.

They both now power on however one of them...
Forum: Video Hardware Repair 08-28-2023, 10:24 AM
Replies: 13
Views: 2,061
Posted By OldAT
Ah there you go, probably comes down to my...

Ah there you go, probably comes down to my mis-understanding of the issue. Thanks for clarifying.
Forum: Video Hardware Repair 08-28-2023, 08:25 AM
Replies: 13
Views: 2,061
Posted By OldAT
So I went back to the problems pdf shared above...

So I went back to the problems pdf shared above and saw the line item:



I pulled that board and found a number of bad 16v 10uf caps and swapped them out. Good as new!

My remaining problem is...
Forum: Video Hardware Repair 08-28-2023, 05:40 AM
Replies: 13
Views: 2,061
Posted By OldAT
Update is good, I recapped that board completely...

Update is good, I recapped that board completely in the end, and the picture was perfect,,,, for the first capture. I realised I needed to change some software settings (not on the vcr) and now...
Forum: Video Hardware Repair 08-24-2023, 12:13 AM
Replies: 13
Views: 2,061
Posted By OldAT
So I removed that board, a bunch of caps are...

So I removed that board, a bunch of caps are reading high ESR and the C1 seems to be dead, Ill get the new parts ordered and report back once I've recapped it. Thanks!
Forum: Video Hardware Repair 08-22-2023, 01:31 AM
Replies: 13
Views: 2,061
Posted By OldAT
Thanks for the tip on the video board. I took at...

Thanks for the tip on the video board. I took at look at the service manual but I'm not sure which one it would be, first thoughts are the IO Pack CBA but Im not sure, I'll attach the layout diagram:
Forum: Video Hardware Repair 08-21-2023, 06:54 AM
Replies: 13
Views: 2,061
Posted By OldAT
Panasonic NV-FS90A video issues, audio fine?

Hey Folks

I've acquired a Panasonic NV-FS90A which seems to have video playback issues on all tapes. Audio does however seem to work just fine.

I've gone through the power supply and replaced...
Showing results 1 to 10 of 10

 

 
All times are GMT -5. The time now is 03:07 PM
Top of Page  -  Site Home  -  Forum Home  -  Archive  -  Forum Policies