Go Back    Forum > Digital Video > Video Hardware Repair

Reply
 
LinkBack Thread Tools
  #1  
04-02-2021, 04:43 PM
Bogilein Bogilein is offline
Free Member
 
Join Date: May 2016
Location: Bavaria
Posts: 256
Thanked 93 Times in 67 Posts
Hello,
is it possible to adjust the video circuit of the JVC SVHS Recorder HR-S8960 without the JVC Jig RCU PTU94023B? Is there a source where you can buy it or another way without using the JIG Remote or a replacement for the original JIG remote?

From the service manual:
Signal (A1) • Ext. S-input
(A2) • Ext. input
(A3) • Color (colour) bar signal [PAL]
Mode (B1) • EE SP
(B2) • S-VHS SP
(B3) • VHS SP
Equipment (C) • Oscilloscope
Measuring point (D) • Y OUT terminal (75Ø terminated)
EVR mode (F1) • Jig code “57”
EVR address (F2) • A : 11
(F3) • Jig code “21” twice
(F4) • Jig code “18” or “19” (Channel +/-)
Specified value (G) • 1.00 ± 0.05 Vp-p
Adjustment tool (H) • Jig RCU [PTU94023B]

(1) Input the signal (A3) from the input point (A1).
(2) Set the VCR to the mode (B1).
(3) Observe the Y OUT waveform at the measuring point (D).
(4) Set the VCR to the EVR mode by transmitting the code
(F1) from the Jig RCU.
(5) Set the EVR address to (F2) by transmitting the code (F3)
from the Jig RCU.
(6) Transmit the code (F4) from the Jig RCU to adjust so that
the Y level of the Y OUT waveform becomes the speci-
fied value (G).
(7) Release the EVR mode of the VCR by transmitting the
code (F1) from the Jig RCU again. (When the EVR mode
is released, the adjusted data is memorized.)
(8) Input the signal (A3) from the input point (A2).
(9) Repeat steps (3) to (7) in the mode (B1).
(10)Record the signal (A3) in the mode (B2), and play back
the recorded signal.
(11) Set the VCR to the manual tracking mode.
(12)Repeat steps (3) to (7) in the mode (B2).
(13)Record the signal (A3) in the mode (B3), and play back
the recorded signal.
(14)Set the VCR to the manual tracking mode.
(15)Repeat steps (3) to (7) in the mode (B3).
Reply With Quote
Someday, 12:01 PM
admin's Avatar
Ads / Sponsors
 
Join Date: ∞
Posts: 42
Thanks: ∞
Thanked 42 Times in 42 Posts
  #2  
04-02-2021, 04:52 PM
lordsmurf's Avatar
lordsmurf lordsmurf is online now
Site Staff | Video
 
Join Date: Dec 2002
Posts: 13,509
Thanked 2,449 Times in 2,081 Posts
There was a recent discussion about the JIG. Somebody was going to send me some sort of device that could replicate the commands, but then I never heard back on it. I'm too busy to chase that down, but I'd do it if given clear how-to info. I have a JIG, but not selling it, not lending it. If we can replicate the buttons, I'd like to do that.

- Did my advice help you? Then become a Premium Member and support this site.
- For sale in the marketplace: TBCs, workflows, capture cards, VCRs
Reply With Quote
  #3  
08-07-2021, 11:04 PM
drzapp drzapp is offline
Premium Member
 
Join Date: Dec 2018
Posts: 97
Thanked 10 Times in 8 Posts
In looking around for a JIG, I came across this post about replicating it- https://www.avsforum.com/threads/jvc...4023b.1531093/
I don't know enough to understand how to do it though.
Reply With Quote
Reply




Similar Threads
Thread Thread Starter Forum Replies Last Post
Looking for JVC JIG remote control PTU94023B ATI_hobby Marketplace 0 02-03-2021 01:18 PM
Horizontal adjust? mikeG Capture, Record, Transfer 5 07-02-2019 02:44 PM
Cannot adjust tracking on VCR in LP/SLP mode anymore? Dude111 Video Hardware Repair 3 12-15-2018 10:53 AM
How to adjust very loud audio clipping during capture? moxiecat Capture, Record, Transfer 6 03-07-2012 05:37 AM
Wanted: PTU94023B "Jig" remote for JVC SR-V10U S-VHS vcr dad2 Marketplace 7 07-23-2011 05:34 AM

Thread Tools



 
All times are GMT -5. The time now is 07:31 AM